Dialog 11, Heidenhain prg in dialog 11 setzen

Hilfe, habe eine Kontur, soll diese auf einer Dialog 11 Steuerung fahren, nur will die Steurung es nicht fahren. Habe es jetzt für die Heidenhain geschrieben, es läuft, nur brauch ich es für die Dialog Steuerung.

01 L X-47.454 Y+42.657 R0 FMAX
02 L Z+5 R0 FMAX
03 L Z-4 R0 FMAX
04 L Z-9 F332
05 CC X-45.557 Y+43.289
06 C X-45.557 Y+41.289 DR+
07 CC X-45.557 Y+43.289
08 C X-44.926 Y+41.391 DR+
09 CC X-43.19 Y+36.172
10 C X-43.19 Y+41.672 DR-
11 CC X-43.19 Y+36.172
12 C X-40.174 Y+40.771 DR-
13 CC X-38.255 Y+43.698
14 C X-38.255 Y+40.198 DR+
15 CC X-38.255 Y+43.698
16 C X-35.638 Y+41.375 DR+
17 CC X-40.499 Y+45.69
18 C X-34.489 Y+43.212 DR+
19 CC X-37.725 Y+44.546
20 C X-34.225 Y+44.546 DR+
21 CC X-37.725 Y+44.546
22 C X-35.813 Y+47.478 DR+
23 CC X-43.19 Y+36.172
24 C X-43.19 Y+49.672 DR+
25 CC X-43.19 Y+36.172
26 C X-56.69 Y+36.172 DR+
27 CC X-43.19 Y+36.172
28 C X-56.543 Y+34.185 DR+
29 CC X-55.554 Y+34.332
30 C X-55.554 Y+33.332 DR+
31 CC X-55.554 Y+34.332
32 C X-54.717 Y+33.785 DR+
33 CC X-47.181 Y+28.864
34 C X-48.743 Y+37.728 DR-
35 CC X-48.83 Y+38.22
36 C X-48.36 Y+38.049 DR+
37 CC X-43.19 Y+36.172
38 C X-44.926 Y+41.391 DR-
39 CC X-45.557 Y+43.289
40 C X-43.557 Y+43.289 DR+
41 CC X-45.557 Y+43.289
42 C X-43.659 Y+43.92 DR+
43 L Z+5 R0 FMAX



Wäre sehr schön, wenn mir jemand helfen könnte
mfg
ducman72

Hallo, das müsste gehen.

N1 X-47.454 Y42.657 G0
N2 Z5 G0
N3 Z-4 G0
N4 Z-9 G1
N6 X-45.557 Y41.289 I-45.557 J43.289 G3
N8 X-44.926 Y41.391 I-45.557 J43.289 G3
N10 X-43.19 Y41.672 I-43.19 J36.172 G2
N12 X-40.174 Y40.771 I-43.19 J36.172 G2
N14 X-38.255 Y40.198 I-38.255 J43.698 G3
N16 X-35.638 Y41.375 I-38.255 J43.698 G3
N18 X-34.489 Y43.212 I-40.499 J45.69 G3
N20 X-34.225 Y44.546 I-37.725 J44.546 G3
N22 X-35.813 Y47.478 I-37.725 J44.546 G3
N24 X-43.19 Y49.672 I-43.19 J36.172 G3
N26 X-56.69 Y36.172 I-43.19 J36.172 G3
N28 X-56.543 Y34.185 I-43.19 J36.172 G3
N30 X-55.554 Y33.332 I-55.554 J34.332 G3
N32 X-54.717 Y33.785 I-55.554 J34.332 G3
N34 X-48.743 Y37.728 I-47.181 J28.864 G2
N36 X-48.36 Y38.049 I-48.83 J38.22 G3
N38 X-44.926 Y41.391 I-43.19 J36.172 G2
N40 X-43.557 Y43.289 I-45.557 J43.289 G3
N42 X-43.659 Y43.92 I-45.557 J43.289 G3
N43 Z5 G0


Sag bescheit

Gruss Mr_X

thats good, but you must give first the G command
for G0, is no need for Feed, i thing its going thet way:



N1 G0 X-47.454 Y42.657
N2 G0 Z5
N3 G0 Z-4
N4 G1 Z-9 (F100)
N6 G3 X-45.557 Y41.289 I-45.557 J43.289 (F100)
N8 X-44.926 Y41.391 I-45.557 J43.289
N10 G2 X-43.19 Y41.672 I-43.19 J36.172 (F100)
N12 X-40.174 Y40.771 I-43.19 J36.172
N14 G3 X-38.255 Y40.198 I-38.255 J43.698
N16 X-35.638 Y41.375 I-38.255 J43.698
N18 X-34.489 Y43.212 I-40.499 J45.69
N20 X-34.225 Y44.546 I-37.725 J44.546
N22 X-35.813 Y47.478 I-37.725 J44.546
N24 X-43.19 Y49.672 I-43.19 J36.172
N26 X-56.69 Y36.172 I-43.19 J36.172
N28 X-56.543 Y34.185 I-43.19 J36.172
N30 X-55.554 Y33.332 I-55.554 J34.332
N32 X-54.717 Y33.785 I-55.554 J34.332
N34 G2 X-48.743 Y37.728 I-47.181 J28.864
N36 G3 X-48.36 Y38.049 I-48.83 J38.22
N38 G2 X-44.926 Y41.391 I-43.19 J36.172
N40 G3 X-43.557 Y43.289 I-45.557 J43.289
N42 G3 X-43.659 Y43.92 I-45.557 J43.289
N43 G0 Z5

@ Mr_X

Das Problem ist geblieben: Radius Abweichung zu groß!!!
Habe es nun anders gelöst.
Trotzdem, danke für die Bemühungen.

Ducman72