537.888 aktive Mitglieder*
3.471 Besucher online*
Kostenfrei registrieren
Anmelden Registrieren
INDEX-Werke // INDEX TRAUB Forum

TND 200 1991/1992, Parameters

Beitrag 27.01.2021, 13:37 Uhr
MACS
MACS
Member
*
Gruppe: Mitglied
Mitglied seit: 21.10.2017
Beiträge: 5

Dear All

I have two machine TRAUB TND 200 with TX8F:
I have a huge problem to find any one who have the some machine the nearest I found TND 160 but it seems the parameters are a little different.
If some one can help.
I think the biggest problem is with M_PARAM 12 [BIT-SELECT]
The machine have driving tools, chip conveyer and hydraulic tail stock, Revolver BARUFFALDI.
I have comunnication with the machine by RS without problem on both side.
I only heard about adoption procedure but no one was ready to visit and fix the machine.

Rigt now Machine START-UP, Hydraulic START UP, I can move X, Z axies and run chip conveyer that's all.
No possible to move revolver, tailstock, cooling pump, ...
Please help me of if it is possible share the photo directly from Your machine
Angehängte Datei(en)
Angehängte Datei  TRAUB_TND200.jpg ( 1.11MB ) Anzahl der Downloads: 9
 
TOP    
Beitrag 28.01.2021, 16:55 Uhr
KBess
KBess
Level 1 = IndustryArena-Lehrling
*
Gruppe: Mitglied
Mitglied seit: 20.06.2019
Beiträge: 7

Hello,

i have had the same pronlem 1 year ago. If you have the machine number give Index a call. They will send you the Parameter list.

My machine have no chip conveyer

M_Parameter 12 BIT SELECT TND200 o. Sore + Späfö
Maschine mit C-Achse, rot. Werkzeug, mit Reitstock
#1 00101111
#2 01011111
#3 01111100
#4 00000011
#5 00000100
#6 10010000
#7 00000010
#8 01000000
#9 10000000
#10 00001000
#11 00000000
#12 00000000
#13 00000100
: 00000000
#17 00000001
#18 10000000
: 00000000
#20 00010100
: 00000000
#24 00010000
#25 00001000
: 00000000
#27 00010000
: 00000000
#33 10000001
: 00000000
#50 00000111
: 00000000
#57 00001001
: 00000000
#61 00000001
: 00000000

Regards
TOP    
Beitrag 28.01.2021, 18:47 Uhr
MACS
MACS
Member
*
Gruppe: Mitglied
Mitglied seit: 21.10.2017
Beiträge: 5

Many Thanks a lot.

I have orginal document from MELDAS but when I put in by hand the machine even don't turn hydrulics.
I attached file with Parameters which I recived from TRAUB-INDEX accoding to Machine No. PARA3 but this wich I try is from 160 PARA2.
Today I got RED surprise.

Best Regards
Angehängte Datei(en)
Angehängte Datei  PARA2.txt ( 3.83KB ) Anzahl der Downloads: 2
Angehängte Datei  PARA3.txt ( 4.07KB ) Anzahl der Downloads: 1
Angehängte Datei  TND200_RED.jpg ( 406.13KB ) Anzahl der Downloads: 5
 
TOP    
Beitrag 28.01.2021, 19:33 Uhr
KBess
KBess
Level 1 = IndustryArena-Lehrling
*
Gruppe: Mitglied
Mitglied seit: 20.06.2019
Beiträge: 7

Hi,

not shure - your battery of the cnc is down? Let the machine switched on for a couple of hours.

With the 2 files - i can not read parameters (or programs) into the machine. Index send me a list which i type direct in the machine.

Regards

Der Beitrag wurde von KBess bearbeitet: 28.01.2021, 19:39 Uhr
TOP    
Beitrag 29.01.2021, 00:42 Uhr
MACS
MACS
Member
*
Gruppe: Mitglied
Mitglied seit: 21.10.2017
Beiträge: 5

Thanks a lot again. I change first only two batteries which I saw now I read that there is also next in the cards.
I will change them tomorrow.

I aso recived the Parameters from Index-Traub directly but it seems I am not lucky person.

It is possible to share this by e-mail I wrote on Prviate message. I will try maybe Your configuration will start working ?

Regards


TOP    
Beitrag 01.02.2021, 23:54 Uhr
MACS
MACS
Member
*
Gruppe: Mitglied
Mitglied seit: 21.10.2017
Beiträge: 5

Dear Sirs

At first I would like to MANY THANKS for help from Index-TRAUB Service. I recived file with some proper parameters I think.

The machine start talk only 4 problems still don't close the subject:
1. Confirmation of hydraulic chuck close / open. I suspect indicator or timer settings/delay between hydraulics and Indicator ?
2. Tailstock not moving
3. BARUFFALDI settings or how to SET-UP properly in the PLC-SW #38 00001100 right now ?
4. Parameters for driven tools ?

If any one have the some machine please help.
Regards
TOP    
Beitrag 22.02.2021, 22:49 Uhr
MACS
MACS
Member
*
Gruppe: Mitglied
Mitglied seit: 21.10.2017
Beiträge: 5

Hello All

Today next huge progress thanks Service TRAUB from GERMANY.
I at least :
1. Rotate the spindle even together with live tool spindle ?
2. Still have problem with BARUFFALDI sometime change 1 or 2 position forward or backword then stock.

Any one can share Parameters for live tools in TND 160/200/300/400 or any other from 90-96 ???

Angehängte Datei(en)
Angehängte Datei  CS_TND200.png ( 1.24MB ) Anzahl der Downloads: 7
 
TOP    



1 Besucher lesen dieses Thema (Gäste: 1)
0 Mitglieder: